Professionally installed interior drainage that manages groundwater and hydrostatic seepage before it reaches your finished floor or stored belongings.
Effective, proven, and installed without disturbing your yard or exterior features.
Interior systems are installed entirely from inside the basement, eliminating the landscaping and hardscaping disruption that exterior work requires.
Perimeter channels capture water as it enters at the floor-wall joint and route it to a sump pit before it can spread across the basement floor.
Interior drainage is not weather-dependent. Installation can proceed in winter months when exterior excavation and membrane work are not feasible in New London, MN conditions.
Properly designed interior channel systems use gravity to route water to the sump pit without mechanical assistance, supplemented by the pump only when pit level reaches the activation threshold.
Interior drainage systems in New London are installed by saw-cutting a trench around the interior perimeter of the basement floor slab, typically four to six inches wide and deep enough to reach the footing level or just below the slab. This trench is the channel that collects water entering at the floor-wall joint and routes it by gravity toward the sump pit. The saw-cutting process is performed with diamond-blade equipment that produces a straight, controlled cut without excessive vibration damage to the surrounding slab. Dust is a natural byproduct of this process, and our crews use containment and ventilation practices to minimize spread to finished areas of the home.
Perforated channel systems offer specific advantages over simple gravel-and-pipe installations in New London basements with block or stone foundations. The channel profile is engineered to sit at the footing level where hydrostatic pressure concentrates, and the wall flange extension captures seepage that occurs at the bottom course of block rather than strictly at the floor-wall joint. This distinction matters because without the wall flange, water running down the interior wall face bypasses the channel and spreads across the floor before reaching the collection point. Proper channel specification requires understanding where the moisture entry is actually occurring, which the assessment process documents before any installation begins.
Sump pit sizing for an interior drainage system in New London requires calculating the expected inflow volume per pump cycle to determine the minimum useful pit capacity. A pit that is too small forces rapid pump cycling, which increases motor wear and reduces system reliability. Our pit specifications for New London installations account for the channel length feeding the pit, the soil permeability documented during the assessment, and the seasonal inflow patterns typical for your area of New London, MN. These calculations are not guesswork; they are based on the same hydraulic principles used in commercial drainage design, applied to residential scale.
The honest tradeoffs of interior drainage versus exterior waterproofing are something we address directly during every assessment in New London. Interior drainage is less invasive, faster to install, unaffected by seasonal weather constraints, and generally less expensive per linear foot than exterior excavation and membrane work. However, it does not eliminate the moisture that is contacting the wall surface; it captures and removes water after it enters the building envelope. For homeowners whose primary concern is protecting finished basement space from water accumulation on the floor, interior drainage addresses that objective effectively. For homeowners concerned about long-term wall deterioration from moisture contact, or whose walls show active spalling and efflorescence from chronic wet conditions, the exterior treatment addresses the wall moisture directly. When both conditions are present in the same structure, we discuss a combined approach that treats both the wall surface and manages floor-level seepage.
From perimeter channel installation to sump integration and annual service, a complete interior drainage solution.
Saw-cut perimeter channel around the full basement footprint, with gravel bed, drainage channel, and sump pit connection. Complete protection for all four walls in one installation.
Learn moreFor New London homes where moisture entry is concentrated on one or two walls, targeted channel installation along the affected sections provides effective protection at lower cost than full perimeter treatment.
Get an assessmentThe wall flange component extends the drainage channel up behind the base of the wall to capture moisture migrating down the wall face before it reaches the floor.
Ask about wall flangesPit location decisions consider channel slope, discharge routing, basement layout, and finished area constraints. We document the reasoning for every pit placement recommendation.
Plan your pit locationExisting interior drainage channels can become clogged with sediment, mineral deposits, or root intrusion over time. We inspect, flush, and repair existing systems in New London homes to restore full drainage performance.
Schedule an inspectionExpansion scopes are common when a homeowner finishes additional basement space and discovers that the existing partial channel does not cover the newly used area.
Expand your systemFour stages from assessment to operational system, each one documented and verified before the next begins.
The assessment produces a written condition report that forms the basis for every specification decision in the installation plan. No work is designed without this foundation.
Cut dimensions are verified before the gravel bed is placed to confirm the channel profile will sit at the correct elevation relative to the footing.
Gravel bed placement, drainage channel positioning, wall flange installation where specified, and sump pit connection are completed in sequence. Channel slope is verified with a level to confirm gravity-assisted flow toward the pit throughout the entire system.
New concrete is poured over the channel system, restoring the floor surface and permanently enclosing the drainage installation. After cure, the full system is tested by introducing water at multiple points along the channel and verifying flow to the sump pit and pump activation.
The results our New London clients experience speak clearly.
I appreciated that the technician was honest about what interior drainage would and would not fix. He identified one wall crack above the floor joint that needed injection treatment, separate from the drainage install, and explained why. That kind of transparency makes a real difference.
From the assessment call to installation completion, everything was communicated clearly. The written proposal broke down every component and I understood exactly what was being installed and why before any work began.
The channel routing around our finished laundry room was handled cleanly. You cannot see where the channel runs under the new concrete. Professional work throughout.
Clear, direct answers from a drainage technician perspective, not a sales script.
The specific installation procedure varies slightly based on foundation type, existing slab thickness, and moisture entry pattern. Block foundations may require weep holes drilled at the base of the block to allow water trapped in the hollow cores to drain into the channel. Poured concrete foundations with floor-joint seepage are typically addressed with the channel profile alone. Our installation crew documents the method used for each wall section and provides this information at project completion.
Interior drainage is a long-term system, not a temporary repair, when it is properly installed and the channel is correctly sized for the inflow volume. The channel system itself has no moving parts and requires no maintenance beyond occasional inspection. The gravel bed does not compact or break down under normal conditions. The drainage profile materials used in quality installations are rated for permanent soil-contact use. Systems installed decades ago continue to perform when the sump pump is maintained and the channel has not been blocked by slab settlement or debris infiltration.
Interior drainage typically costs less per linear foot than exterior excavation and membrane waterproofing, primarily because the excavation equipment, soil management, and backfill work associated with exterior projects add significant cost to that scope. For most standard residential configurations in New London, interior drainage is a more budget-accessible solution. However, cost comparison alone should not drive the decision; the correct approach depends on the moisture entry mechanism present in your specific basement. Installing interior drainage to address a problem that is fundamentally an exterior membrane failure will provide comfort improvement but will not stop ongoing wall contact moisture, which continues to deteriorate the wall material.
Standard full perimeter interior drainage installation for a typical single-story New London basement is completed in one working day. Partial perimeter systems on one or two walls are typically finished in half a day. Basements with complex layouts, finished areas requiring careful routing, or multiple existing pipe penetrations crossing the channel path may extend the installation to a second day. We provide an accurate time estimate after the assessment so homeowners can plan for the dust and noise associated with saw-cutting, which is the most disruptive phase of the installation.
An interior drainage channel system requires minimal maintenance because it has no moving parts. The primary maintenance task is ensuring the sump pump connected to the system is in good working order, which involves the same inspection protocol as any pump: float switch testing, motor operation check, discharge line inspection, and battery backup readiness verification. The channel itself should be visually inspected at accessible cleanout points annually if the design includes them, or whenever pump performance changes in a way that might indicate a channel blockage. Older channel installations in some New London homes show calcium and mineral deposit buildup over many years, which can be addressed with periodic flushing.
Interior drainage can be installed in a finished basement, though the process requires more planning and may involve temporary disruption of finished flooring and baseboard materials along the channel route. The saw-cutting must follow the perimeter regardless of what is installed above it, so finished flooring within the cut zone will need to be removed before work begins and replaced after the concrete cap cures. Drywall along the base of finished walls is typically removed at least partially to allow the wall flange to be installed properly. We document all disruption areas in the installation plan so homeowners can arrange for finish materials before scheduling the work.
Our certified drainage technicians serve New London and surrounding New London, MN communities. Call today for a free on-site assessment.
Call +1-866-476-1348 for Assessment